TL;DR: To stop bathroom condensation and mould, remove moist air with a good extractor fan, keep the room and its surfaces warm, and dry wet surfaces quickly after a shower or bath.
- Condensation forms when warm, moist air meets a cold surface, which is why it gets worse in winter.
- Run an extractor fan during your shower and for a while after; check it is moving air.
- Choosing a fan: at least 15 litres per second for a bathroom, ideally with a humidity sensor or overrun timer, ducted to the outside.
- A heated towel rail warms the room and dries towels, so less moisture hangs around.
- Squeegee the shower screen and wipe tiles; sealed grout or wall panels hold less moisture.
- Persistent damp that comes back after cleaning may need a closer look at ventilation or the building.
Bathroom condensation happens when warm, moist air from a shower or bath hits a colder surface, like a window, outside wall or mirror, and turns back into water. In winter the walls are colder and the windows stay shut, so it gets worse. If those surfaces stay damp, mould can grow, usually in grout, sealant and corners.
The fix comes down to three things: remove the moist air, keep surfaces warm, and dry what gets wet.
1. Ventilate: get the moist air out
An extractor fan is the most important tool against bathroom condensation. Building Regulations guidance for new work in England (Approved Document F) sets a minimum extract rate for bathrooms of 15 litres per second for an intermittent fan. If your fan is old, noisy or barely moving air, it may not be doing its job.
- Test it: hold a single sheet of toilet paper near the fan while it runs. If it is not pulled towards the grille, the fan or ducting may need attention.
- Run it longer: keep it on during your shower and for a while after. A fan with an overrun timer or humidity sensor does this for you.
- Keep the door shut while you shower, so moisture is extracted rather than spreading into the rest of the house.
- Open the window after a shower if you can, even for a few minutes.
If you are renovating, it is the right time to upgrade the fan and its ducting. Our guide to bathroom renovation costs covers what a full refit involves.
Choosing a bathroom extractor fan
If your bathroom has no fan, or the one you have is not clearing the steam, a new extractor fan is the single best fix for condensation. Here is what to look for.
What size extractor fan?
Fans are rated by how much air they move. Building Regulations guidance for new work in England (Approved Document F) asks for at least 15 litres per second for an intermittent bathroom fan, or 8 litres per second for a fan that runs continuously, and 6 litres per second for a separate toilet or cloakroom. A standard 100mm fan suits most bathrooms, but check the rated extraction rate, as the length of the ducting reduces what the fan actually achieves.
Types of extractor fan
| Type | Where it goes | Best for |
|---|---|---|
| Axial fan | Wall, window or ceiling | Short duct runs straight to the outside |
| Inline or mixed flow fan | In the loft or ceiling void | Longer duct runs and more powerful extraction |
| Continuous running fan | Wall or ceiling | Runs quietly all the time and boosts when you shower |
Timers and humidity sensors
- Overrun timer: keeps the fan running for a set time after you switch the light off.
- Humidity sensor (humidistat): switches on when the air gets damp and off when it clears, so you never forget.
- Motion sensor: switches the fan on when someone walks in, useful for a cloakroom.
Where should an extractor fan go?
- High on the wall or in the ceiling, where warm, moist air collects.
- Close to the shower or bath, and ideally on the opposite side of the room from the door, so fresh air is drawn across the room.
- Ducted to the outside, never into the loft. In a cold loft, use insulated ducting so condensation does not run back down into the fan.
- Keep duct runs short and as straight as possible.
Fans above the bath or shower
A fan fitted in the zone directly above a bath or shower must be rated for it, usually at least IPX4, and many fans for that position are low-voltage (SELV) models. Bathroom electrics should always be fitted by a qualified electrician.
Quiet fans
Noise is the main reason people switch fans off. Compare the noise level in decibels (dB) before you buy: a quieter fan is more likely to be left running for as long as it is needed.
2. Heat: keep the room and surfaces warm
Warm surfaces collect less condensation. A bathroom that is heated steadily dries out faster than one that is only warmed for ten minutes in the morning.
- A heated towel rail or towel radiator warms the room and dries your towels, so they don't release moisture for hours. See our heated towel rails, our heated towel rail guide and our traditional towel radiator guide.
- Size it properly. A rail covered in wet towels gives out less heat, so a bigger rail or a second radiator helps in a cold room.
- Think about summer too. An electric towel rail or a dual fuel element keeps towels drying when the central heating is off.
3. Dry: deal with wet surfaces quickly
- Squeegee the glass and tiles after each shower. It takes a minute and stops water sitting on the surface.
- Hang towels to dry on a heated rail rather than in a pile.
- Leave the shower screen or curtain open afterwards so the space can air.
- Wipe the window sill if water collects on it.
Surfaces that resist mould
Mould needs moisture and something to grow on. Grout and silicone are where it usually starts. When you renovate, a few choices make life easier:
| Surface | Why it helps |
|---|---|
| Shower wall panels | Large panels with few joints, so there is less grout to hold moisture. See Showerwall panels. |
| Large-format tiles | Fewer grout lines than small tiles. See our tiles. |
| A walk-in screen | An open-sided shower airs out faster than a fully enclosed cubicle. See our walk-in shower screens guide. |
| Wall hung furniture | Air can circulate underneath, and the floor is easy to clean and dry. See vanity units. |
We compare panels and tiles in more detail in shower wall panels vs tiles.
Cleaning mould you already have
For small patches on tiles and grout, a bathroom mould cleaner and a stiff brush usually work. Follow the product instructions, ventilate the room while you clean and wear gloves. Mould that has grown into silicone sealant often can't be cleaned out, so the best fix is to cut out the old sealant and reseal once the area is completely dry.
When it is more than condensation
If damp patches come back quickly, appear away from the shower, or the plaster feels soft, the cause may be a leak, poor ventilation in the wider house, or damp coming through a wall. Those need investigating properly before you redecorate. Long-term damp and mould can also affect health, so it is worth dealing with rather than living with.